The NT series is a reduction gear mixer using a high precision helical gear designed exclusively for mixers.
It has provides a compact design of the mixer and the motor by positioning the motor on the side of the mixer.
The mechanical seals and reduction ratios can be changed easily by opening the top cover of the mixer without having to remove the motor
The NSR type mixer It is a low-noise, long-life and light-weighted compact mixer with a reliable reduction gear durable for use in many applications.
The sizing of the optimum power, rotation number, and impeller is made possible due to our accumulated experience.
The NSR series can be equipped with grand packing seals, water seals, and mechanical seals.
The GSE type mixer is a side entry type mixer which allows it to be applied to the side of the mixer.
A shutoff off device allows the replacement of the seal unit and the gear box to be replaced with the shaft and impeller still inside the tank.
The turnbuckle adjustment allows operation with of the mixer with minimal vibration.
A large number of this series have been delivered to many FGD plants across in Japan and have recevied high priase for its reliable performance.
The AE series is a smart-type electric valve actuator that enables multiple controls by digitalizing torque detection and position detection.
This jack holds the same high functions as a normal screw jack, just a lot smaller and lighter.
It is very easy to use and handle.
Basic capacity: 2kN / 5kN
Reduced as much weight as possible while maintaining endurance.
The case is compact and could be attached to the upper or lower side.
Can self-lock in any position within the stroke.
Variety of options like the bellows type protection of the screw shaft, limit switch for control, and RC encoder.
Multi-purpose standard type screw jack which self-locks.
Structured by a highly accurate worm gear and a trapezoid shaped screw shaft. Brakes not required for standard use.
Basic capacity: 10–1000kN
Can self-lock in any position within the stroke.
Screw shaft is made of carbon steel (right screw). We also offer ones with twist stopper key.
The speed reducer part uses grease lubrication, allowing smooth movements and long time use.
Variety of options like the bellows type protection of the screw shaft, hand wheel for manual operation, trunnion base, limit switch for control, and RC encoder.
A high efficient, high-speed, and high frequent new generation jack made by combining a bevel gear and high lead ball screw.
Contributes to productivity and energy saving / environmental measures. Besides the standard ascending / descending function, it can be used for a variety of purposes.
Basic capacity: 5–50kN
Screw shaft speed: MAX20m/min. 5 times faster than a ball screw jack.
Operation frequency: MAX70%ED. 5 times more frequent than original products.
Input rotation: MAX2000–3000min-1. Runs in a wide range using a servomotor.
No self-lock function. Brakes needed for maintenance.
This ball small jack is an extremely compact, lightweight, and easy-to-use jack, which is able to deliver high performance similiar to standard ball jacks.
Basic capacity: 4kN
Reduced as much weight as possible while maintaining endurance.
The case is compact and could be attached to the upper or lower side.
Highly efficient and high-speed operation made possible from rotating friction.
An application to prevent the screw shaft from rotating is available.
No self-lock function. Brakes needed for maintenance.
Variety of options like the bellows type protection of the screw shaft, limit switch for control, and RC encoder.
Standard type screw jack that uses a ball screw shaft. Highly efficient and optimized for high-speed operations. Antipollution measures in place with small amounts of head and noise even during high-speed operations.
Basic capacity: 10–1000kN
Rolling motion between the nut and screw is same as ball bearings. Compared to the screw jack, it is 3 times more efficient and conserves energy.
No self-lock function. Brakes needed for maintenance.
An application to prevent the screw shaft from rotating is available.
Variety of options like the bellows type protection of the screw shaft, trunnion base, limit switch for control, and RC encoder.
This type of jack is compact and lightweight, yet delivers high performance similar to standard screw jacks. It is easy to use while realizing high efficiency and high speed.
Basic capacity: 2–10kN
Multiple port screws with 4 outlets used, high-speed from high lead specifications.
2–5 times faster than the original screw jack.
The case is compact and could be attached to the upper or lower side.
No self-lock function. Brakes needed for maintenance.
Variety of options like the bellows type protection of the screw shaft, limit switch for control, and RC encoder.
High lead type ball screw jack using a ball screw shaft, optimized for high-speed operation.
Basic capacity: 4–200kN
Uses high lead ball screws. Compared to standard type ball screw jacks, faster ascending / descending made possible in the same number of input rotations.
Rolling motion between the nut and screw is same as ball bearings. Compared to the screw jack, it is 3 times more efficient.
An application to prevent the screw shaft from rotating is available.
No self-lock function. Brakes needed for maintenance.
Variety of options like the bellows type protection of the screw shaft, trunnion base, limit switch for control, and RC encoder.
This jack series is the intermediate type between the small screw jack and the ball small jack. The lifting screw is made of stainless steel and for the traveling nut types, the traveling nut is made of PET (polyethylene terephthalate).
Basic capacity: 2kN/5kN
Very light-weight design while maintaining endurance.
The case is compact and could be attached to the upper or lower side.
Conserves space as steel spheres and return tubes are not required.
An application to prevent the screw shaft from rotating is available.
No self-lock function. Brakes needed for maintenance.
Variety of options like the bellows type protection of the screw shaft, limit switch for control, and RC encoder.
Simple structure using a rack gear and is a highly efficient jack with high-speed conversion of straight line operation and rotating operation.
Basic capacity: 2–4kN
High-speed straight line operation is possible even when the input shaft is rotating at slow speed.
3 types of screw end fitting can be used.
No self-lock function. Brakes needed for maintenance.
Less power loss and outstanding machine efficiency.
The attaching side of the product has an horizontal and vertical sides to choose from.
Variety of options like the bellows type protection of the screw shaft, limit switch for control, and RC encoder.
Lifting Sytem for synchronized operation of multiple jacks.
Jacks are linear actuators that can easily realize accurate quantitative motion, and are perfectly suitable for synchronized operation of multiple jacks. Especially, depending on the weight and size of loads, it will be difficult to lift the loads with a single jack. A interlocking system of multiple jacks are effective.
Various system arrangements are possible; for example, interlocking 2, 3, or 4 jacks for synchronized operation.
We also offer rust-proof and low dust discharging jacks, which are the best for lifting/lowering, or opening/closing large devices in a clean environment.
As an option we are able to attach motors to our screw jacks, which increases the variety of places our jacks could be used in. We are able to provide a motor capacity variety of 0.1kW to 3.7kW.
Can be used immediately after installation as it comes with a geared motor.
Uses a small, light, and quiet geared motor. Fine inverter drive motor characteristic. Can be used in a wider range of torques when combined with an inverter.
1/3 standardized against reduction gear ratio of geared motors.
Custom Series -low dust generation jack for clean environments.
Based on ball screw jack with customization of low dust specification
Servomotors can be selected as the drive power
In clean environments that require low dust generation, proper rust-proof process and lubricant selection are required. We deliver "clean type jacks" which achieved low dust generation by application of appropriate grease/paint, strong seals, and stainless steel material.
Marketing
Nippon Gear Co., Ltd.
Irvine , California
